FLIR Radiometric Lepton Dev Kit 紅外線熱成像開發套件 2019新版 Sparkfun 進口 熱成像儀 紅外線熱像儀


Availability: 1 件庫存 貨號: SNR-003261 分類: 標籤: , , , , , ,


FLIR Radiometric Lepton Dev Kit 紅外線熱成像開發套件 2019新版 Sparkfun 進口 熱成像儀 紅外線熱像儀

FLiR Dev Kit 紅外線熱成像開發套件 包括一個擴展板以及Lepton®長波紅外(LWIR)成像器。使用該套件,您可以將 FLiR 的熱成像可靠性和功能帶入您的Arduino,Raspberry Pi或任何基於ARM的開發工具,並且易於使用麵包板包裝。您只需將Lepton®成像儀模塊安裝到提供的分線盒中,連接接線頭,即可在任何時間看到完全黑暗的環境!

每個FLiR開發工具包中包含的Lepton®LWIR模塊可用作一種相機,並將80×60像素的分辨率打包到一個小於一角硬幣的相機機身中,並在其標稱響應波長頻帶捕獲紅外輻射輸入(從8到14微米)並輸出均勻的熱圖像。同時,這些套件中的每個分線板都提供Lepton®電源插座,25Mhz晶體振盪器,100mil插座,用於麵包板或任何主機系統的接線。關於此套件需要考慮的一些事項:分線板將接受3-5V輸入,並根據Lepton®的要求進行調節,從Lepton模塊讀取圖像,只需要一個SPI端口,然後配置攝像頭您還需要一個I 2 C端口,但這不是必需的。


FLIR Radiometric Lepton Dev Kit  紅外線熱成像開發套件 特色

  • LWIR傳感器,波長為8至14μm
  • 50°HFOV,60°對角線
  • 80(h)×60(v)個有效像素
  • 熱靈敏度<50 mK
  • 輻射精度(35°C Blackbody)大於:
    • 高增益:在25°C時±5C
    • 在25°C時低增益±10C
  • 像素尺寸:17微米
  • 幀速率:9 Hz。
  • 輸出格式:用戶可選的14位,8位(AGC應用)或24位RGB(應用AGC和著色)
  • SPI視頻接口
  • 雙線I 2 C式串行控制接口
  • 快速成像(<1.2秒)
  • 低工作功率,標稱值為150 mW(在整個溫度範圍內<160 mW)


The FLiR Dev Kit includes a breakout as well as a Lepton® longwave infrared (LWIR) imager. With this kit you will be able to bring FLiR’s thermal imaging reliability and power to your Arduino, Raspberry Pi, or any ARM based development tool all in an easy to access breadboard friendly package. All you need to do to get this kit set up, simply attach the Lepton® imager module into the provided breakout, connect the headers, and you will be seeing in full darkness in no time!

The Lepton® LWIR module included in each FLiR Dev Kit acts as a sort of camera and packs a resolution of 80 × 60 pixels into a camera body that is smaller than a dime and captures infrared radiation input in its nominal response wavelength band (from 8 to 14 microns) and outputs a uniform thermal image. Meanwhile, each breakout board in these kits provides the socket for the Lepton®, power supply’s, 25Mhz Crystal Oscillator, 100 mil header for use in a breadboard or wiring to any host system. A few things to consider about this kit: the breakout board will accept a 3-5V input and regulate it to what the Lepton® wants, to read an image from the lepton module all you need is an SPI port, and to configure the camera settings you also need an I2C port, although this is not required.

Note: This kit comes in two separate parts and will need to be assembled once received. The Lepton® module is extremely sensitive to electrostatic discharge (ESD). When inserting it into the breakout board be sure to use proper personal grounding, such as a grounding wrist strap, to prevent damage the module.

  • LWIR sensor, wavelength 8 to 14 μm
  • 51-deg HFOV, 63.5-deg diagonal
  • 80 (h) × 60 (v) active pixels
  • Thermal sensitivity <50 mK
  • MIPI and SPI video interfaces
  • Two-wire I2C-like serial-control interface
  • Fast time to image (< 0.5 sec)
  • Low operating power, nominally 150 mW (< 160 mW over full temperature range)



搶先評價 “FLIR Radiometric Lepton Dev Kit 紅外線熱成像開發套件 2019新版 Sparkfun 進口 熱成像儀 紅外線熱像儀”